Tuesday, August 6, 2013

How To Replace The Tank Seals On A Toilet

Introduction


This toilet has been bugging me for some time. The handle sticks, and causes the toilet to run for long periods of time. And the tank to bowl seal was leaking, making the toilet turn on about every 10 minutes. This bathroom sits right above my home office, and I would have to listen to the water click on and off, for what was probably several weeks before I got around to fixing it.

It was very aggravating, so I decided to spend some extra time on it and make everything perfect. I don't have time to fix the same stuff twice.

The Tools



ToolPurpose
Channellock PliersTake off the water supply to the tank and for the overflow tube nut
Large Flathead ScrewdriverUsed to loosen / tighten the tank bolts
Half Inch Box WrenchUsed to  loosen / tighten the tank bolts
ScissorsUsed to trim the rubber refill tube
Small HacksawUsed to cut off the old tank bolts if necessary, which it usually is
Putty KnifeUsed to clean out the bottom of the tank


The Job


First I turned off the water supply, then I flushed the toilet. Then I removed the tank lid and kind of scooped as much water as I could into the drain. Then I disconnected the water feed from the tank using a pair of Channel Locks.


How To Rebuild A Toilet - Figure 0

We've owned the house for almost 10 years, so I knew the tank bolts were old and I could see they were badly corroded. I didn't spend much time trying to get one off before I went and grabbed a small hacksaw. They were a real pain to saw off.

How To Rebuild A Toilet - Figure 1

But I got them off, and this was the only real hassle of the project. It's all down hill from here.

How To Rebuild A Toilet - Figure 2

Now, I don't have much experience repairing toilets, but the old tank to bowl gasket below doesn't look like any of the pictures I have seen, or any of the ones I saw at my local hardware store. The wife was going to be at a hardware mega-store the same day, so I had her take the picture below. The guy in the plumbing aisle looked at her and said "Lady, I've been doing plumbing blah blah years and I've never seen a gasket that looks like this one."

How To Rebuild A Toilet - Figure 3

The dogs were helpful as always. Whatever that thing is, Lenny isn't sure he likes it.

How To Rebuild A Toilet - Figure 4

When I got the tank bolts off, and before I did anything else, I took the entire tank as-is and dumped the remaining water into the bathtub right next to the toilet. I guess if you don't have a tub there, you could pour it into a bucket, since it's not that much water.

Next I flipped the tank on its side, as shown below. My Channel Locks barely fit on the big plastic nut, but I did get it off. And then I pushed the overflow tube and the bolts through from the bottom. At this point the tank could sit flat on top of the toilet seat. Well, once I cleaned with with bathroom cleaner.

How To Rebuild A Toilet - Figure 5

My new overflow tube didn't come with a cap on it, and the original cap didn't fit the new tube, so I decided to reuse the old tube, replacing the nut and the seal but leaving the tube and cap.

How To Rebuild A Toilet - Figure 6

The seal wasn't in terrible shape. But it can only be replaced with the tank off, and since I just happened to have a new one, and since I just happened to have the tank off, it was a no-brainer. It'll be 10 more years before the tank has to come off again.

How To Rebuild A Toilet - Figure 7

 This cap looked pretty grungy when I took it off. I scrubbed it in the sink with a scrub brush and disk soap and it actually looked pretty good when I was done.

How To Rebuild A Toilet - Figure 8

With everything cleaned up and a new seal and plastic nut, the whole assembly looked good as new.

How To Rebuild A Toilet - Figure 9

 I even scrubbed the threads on the overflow tube. This is as good of a rebuild as I can get.

How To Rebuild A Toilet - Figure 10

 It's easier to work with the tank when it's just sitting like this on top of the seat. I will not subject my readers to the picture of what the toilet looked like under the tank. Let's just say that most people will want to take the opportunity to clean the whole are before mounting the tank back up. It ended up pretty clean though.

How To Rebuild A Toilet - Figure 11

I kept the water inlet assembly with I replaced a couple years ago. I'm not too worried about it since it's very easy to replace. The whole assembly can be replaced without taking the tank off.

How To Rebuild A Toilet - Figure 12

The handle was sticking, and I would go to use the bathroom in the middle of the night and notice that the water was running. It seemed to stick every few times we used it. This was one of the problems I set out to solve with a rebuild. I took the handle out at this point, for further attention.

How To Rebuild A Toilet - Figure 13

The tank had a lot of silt and debris at the bottom, including some type of silicone beads which came in through the city water supply a couple years ago and really screwed our plumbing up. Good thing we have a water filter or we would've been drinking those things.

How To Rebuild A Toilet - Figure 14

 I used a putty knife to clean the debris out, and then cleaned it out with some bathroom cleaner and paper towels.

How To Rebuild A Toilet - Figure 15

Now the tank looked MUCH better after I cleaned it.

How To Rebuild A Toilet - Figure 16

Much, much better.

How To Rebuild A Toilet - Figure 17

At this point I cleaned off the bottom of the tank and mounted the overflow tube.

How To Rebuild A Toilet - Figure 18

The parts below were all the parts I replaced, except for the new flapper, not shown. The gasket, tank bolt kit and overflow tube kit cost less than $20 total.

How To Rebuild A Toilet - Figure 19

I bought a tank bolt kit from my local Ace hardware store. It came with an extra bolt, but I needed all the nuts and washers that came with it because I have a slightly different tank to bowl gasket than it had before.

How To Rebuild A Toilet - Figure 20

The tank to bowl gasket, also from Ace. I think it was about 5 bucks.

How To Rebuild A Toilet - Figure 21

 First I took the handle assembly into the kitchen and cleaned the handle out in the sink. There was some debris inside the handle, and cleaning it out made it feel much better. Then, I took it out to the garage and sprayed some silicone lubricant spray in it.

How To Rebuild A Toilet - Figure 22

Here the tank bolts are mounted, the new tank to bowl seal is mounted, and the tank is ready to mounted on the toilet. Since I wasn't using whatever gasket/grommet I took off, I had to use the nuts from the tank bolt kit with the rubber washers on both sides. This made for a really robust seal. This thing isn't gonna leak.

On the underside of the tank, I used the remaining 2 nuts, metal and rubber washers, with the rubber washer always going against the ceramic surface.

How To Rebuild A Toilet - Figure 23

I ended up replacing the flapper from the overflow tube kit I had laying around the garage. Notice how long that rubber refill tube is. I ended up cutting most of it off.

How To Rebuild A Toilet - Figure 24

The refill tube was kind of flopping around in there but I decided to leave it that way for now, fill the tank and test the new tank seals. Everything is tight.

How To Rebuild A Toilet - Figure 25

Just a quick check with the level. Wait, what? The whole think is tilting to the right! I must have seated the tank wrong or something.

How To Rebuild A Toilet - Figure 26

So I drain the tank, loosen the bolts, re-position the tank and refill it. After playing around with it some, this is about as good as I can get it. I noticed that Ace had toilet tank shim kits. If my OCD sets in, I'll go buy the shim kit. It's probably always been this way, so I decide to leave it be.

How To Rebuild A Toilet - Figure 27

I ended up digging through the garage and I found the little filler but nozzle and clip I was looking for. Score! The refill tube was really bugging me, so I cut it and attached it to the nozzle, which I attached to the overflow tube.

How To Rebuild A Toilet - Figure 28


At this point, I am done! It has been about a month and not so much as a peep out of it. And the handle hasn't stuck a single time. It's actually a little noisier with the refill tube hooked up correctly, but hey, I'd rather have it working correctly. Now I don't hear it from my office. And I've probably made my 20 bucks back by not having the water click on every few minutes over the last month. Another successful job. The sawing sucked because I'm old and had to stoop uncomfortably and it was hard to get the right angle on it. My friend the plumber says it just takes him a minute, but it took me considerably longer than that. I saved quite a bit of money, though, so it was worth the extra hassle. And I doubt a plumber would've scraped the tank clean or scrubbed some of the components with soap and water. The beauty of doing it myself means I don't need to rush. 

3 comments:

  1. Hello there. This blog is awesome! Very informative. I saw many important tool for plumbing these were very nice and helpful for us. Thank you for sharing.
    Plumber Alabaster, Al

    ReplyDelete
  2. Nice sharing,I am very impressed your expressing way, I really liked this post, Thanks for share with us, I will be come back to your next post, Good luck!!!
    Plumber Homewood, Al

    ReplyDelete