Sunday, September 8, 2013

Replacing Solution Tank For Hoover SteamVac

We've had two Hoover Steamvac V series units for several years. One quit working so I've used it as parts for the other one, and that's worked well. But the water tanks on this model really stink. It's a flawed design where the part of the tank that holds the handle breaks off, causing the tank to hit the floor. But when it hits, the bottom tray that holds the tank pierces the tank in two places. So both of my tanks are pierced on the top and bottom.

We ordered a replacement tank from Amazon which supposedly does not have that design flaw. In fact, the little flyer that comes with it says as much. The replacement tank was about $40, which is expensive, but I'm not ready to buy a new one. The new ones range from $150 to $300, so I'm hoping to keep the one I have alive and working for another year or so. The Hoover Steamvac is a nice little machine other than the tank issues. I noticed that the newer models have the improved tank, so that's something.

Below is one of the old tanks. There was not enough tank material on the top left to hold the handle, so the tank would randomly fall out of the Steamvac during normal use. Not fun. But even worse, every time it fell out, the plastic tray holding the tank would want to pierce the bottom of the tank. I ended up epoxying it several times. The epoxy is stronger than the original plastic, but the tray would still pierce the epoxy and cause it to leak. I even tried filing the sharp plastic clips down with a rotary tool, but it didn't help much. At some point I just couldn't keep the old tank alive any longer.

Hoover SteamVac: Broken Tank- Old Design


The new tank arrived looking much more robust than the original. I sure hope so. The plastic looks thicker and less brittle as well.  Also, the caps on the tank and soap reservoir look much sturdier. The Amazon reviews talk about how much better it is, so hopefully we'll be in good shape.

Hoover SteamVac Replacement Tank

Hoover SteamVac Replacement Tank: Front View

Hoover SteamVac Replacement Tank: Back / Side View


Below is a picture of the paper flyer discussing the new tank, and the improvements over the old tank.

Hoover SteamVac Replacement Tank: Data Sheet


The handle was 10 bucks extra and we already had two, so we didn't order one. I verified that the handle from the existing tank would fit in the new tank, and it does. It was a tight fit, but that's a good thing because I do not want this one to fall out and bounce on the floor.

Hoover SteamVac Replacement Tank With Handle Mounted

Hoover SteamVac Replacement Tank: Closeup Of Handle


Putting the new tank in the Steamvac: it fits perfectly! It even fits better than the old tank. If the rest of your Steamvac works well, then this replacement tank should make it happy.

Hoover SteamVac Replacement Tank Mounted On Unit


Using the new tank: It works well. Since the soap reservoir on both the old tanks had failed, I just got used to mixing the soap and water in the main tank. Now I can go back to keeping the cleaning solution separate from the main tank. Another perk of having the tank work how it's supposed to.

Thursday, September 5, 2013

Replacing The Main Element On An Electric Range

In this post, I will be replacing the main element on a Kenmore Elite electric range, though the repair technique should apply to most makes and models. This is the bottom or "bake" element, not to be confused
Kenmore Elite Electric Range
with the top or "broil" element.

We've had this oven for about 10 years, and overall we've been very happy with it. But recently it just stopped getting hot when set to bake. We can still use it on broil mode, but it's not the same. Good luck with a frozen pizza, and I haven't even tried the bread I used to bake almost daily. With such a busy schedule, it's been out a couple months now, and it's past time to fix it. The wife is starting to complain.

Tools


This is a fairly simple job, so the only tools you will need is a #2 Philips screwdriver and maybe a pair of needle nose pliers to pull the electrical terminals off the old element, or possibly fish them out if they get loose from you.



ToolPurpose
Philips Screwdriver #2Remove / Install the heating element
Needle Nose PliersRemove terminals or fish them out if they get pulled back into oven

Craftsman Philips Screwdriver #2 and Kobalt Needle Nose Pliers

My Oven


Here's the tags from the oven I fixed, in case it helps anyone. I easily found the new element from an online store using the model number from the tags.

Kenmore Elite Model Tag #1

Kenmore Elite Model Tag #2

Step 1 - Remove Old Element


Removing the old baking element should be simple. First, take out the racks if they are in the oven. Now, take a look at how the old element is mounted. You should see two screws either right above or right below it. See them? Those two screws are all that's holding the old element in the oven. If you don't see mounting screws right next to the element, this is not the article you're looking for.

Kenmore Elite Range: Closeup Of Baking Element


Now, take those two screws out, as always being very careful not to strip them. Do not use too small of a screwdriver, and of course, I only use USA made screwdrivers, mainly due to the harder steel that's less likely to strip the screws.

Kenmore Elite Range: Closeup Of Baking Element Mounting Screws


When you have the screws out, you will notice that behind the mounting plate, the element is connected to two electrical terminals. Carefully remove both terminals from the element. Be sure not to let them get pulled back into the oven, or you will have to pull the whole oven and take it apart, which you do not want to do for a simple job like this. When the old element is disconnected, try to leave the two wired dangling in such as a way as they aren't trying to go back inside the oven.

Kenmore Elite Range: Closeup Of Baking Element Connection Terminals
Kenmore Elite Range: Baking Element Removed

Step 2 - Install The New Element


This should be the easiest part. Just set the element down and connect it. Be very careful not to pull on the wires too much or you will break them or snap the solder joints, and yep, you'll be taking the oven apart. Ideally you should not be putting any force on them at all, as there should be just enough slack to connect them to the new element.

Kenmore Elite Range: Aftermarket Baking Element



Kenmore Elite Range: Closeup Of Baking Element Terminals


Once the new element is connected, re-install the mounting screws. Be very careful not to strip or cross thread them as people will laugh at you for botching such a simple job. And for that same reason, I like to do a "reality" check and scan the area for tools left in the appliance or something out of place. Ask yourself "am I going to burn the house down when I turn this thing on?"

Notice that the new element below has a slightly odd shape compared to the stock element, but that's fine.

Kenmore Elite Range: Aftermarket Baking Element Installed


That's it! Assuming the element was the real problem and not a control board or electrical contact issue or something, your oven should now be operational. Ours lasted almost 10 years of extra hard use, so you shouldn't have to worry about the new one burning out any time soon.

Kenmore Elite Range: Aftermarket Baking Element Red Hot!